Do I have to register my wallbox?
Yes. Every wallbox must be registered with the grid operator before it is put into operation, regardless of its power rating. The obligation is set out in § 19(2) of the Niederspannungsanschlussverordnung (NAV, the German Low Voltage Connection Ordinance), which applies to service connections in the low-voltage grid.
The wallbox additionally needs the grid operator's approval if the total rated power of all charging points exceeds 12 kVA per electrical installation. The grid operator must respond within two months of notification. If it refuses, it must state the reasons, possible remedial measures and the time they would take.
| Equipment | Total power | What is required |
|---|---|---|
| 1 wallbox, 11 kW | below 12 kVA | Registration |
| 2 wallboxes, 11 kW each | above 12 kVA | Registration and approval |
| 1 wallbox, 22 kW | above 12 kVA | Registration and approval |
For approval, what counts is the total of all charging points per electrical installation, not the individual unit. Adding a second wallbox later can take you over the 12 kVA limit, and you then need approval even though the first unit was only registered.
Who registers the wallbox, and where?
The wallbox is usually registered with the local grid operator by the electrical contractor who installs it. Your electricity bill shows which grid operator is responsible. Within the city of Munich it is SWM Infrastruktur, which also supplies some surrounding municipalities, for example Kirchheim since 2020. In many municipalities of the Munich district (Landkreis München), Bayernwerk Netz operates the power grid.
At SWM Infrastruktur, charging points up to 11 kW require registration and larger ones require approval. For small wallboxes a registration form sent by e-mail or post is sufficient; approval is handled through the grid connection portal. For wallboxes above 4.2 kW, the electrical contractor also registers the unit as a controllable consumer device in the commissioning portal after commissioning. The contractor must be listed in the register of approved installers of a distribution system operator. Before registration, the meter cabinet is prepared for the control equipment.
Bayernwerk Netz accepts wallbox registrations online. Either the customer or their electrician can submit it. According to Bayernwerk, registration and the grid compatibility check are free of charge. If the capacity of the service connection has to be increased, a separate application in the grid connection portal is required.
Note: Installing a wallbox is a job for a qualified electrical contractor. The Verbraucherzentrale (consumer advice centre) expressly points out that charging stations may only be installed by a qualified contractor.
What does § 14a EnWG mean for a wallbox?
Since 1 January 2024, a private wallbox drawing more than 4.2 kW from the grid counts as a controllable consumer device under § 14a EnWG (Energiewirtschaftsgesetz, the German Energy Industry Act). The grid operator may limit its power if the grid is at risk of overload. According to the Bundesnetzagentur (Federal Network Agency), at least 4.2 kW must always remain available, so charging does not stop.
In return you pay reduced grid fees. You choose one of three modules; if you do not choose, Module 1 applies.
| Module | Benefit | Requirement |
|---|---|---|
| Module 1 | Flat-rate reduction per year, €110 to €190 according to the Bundesnetzagentur (as of 2023); your grid operator states the current amount in its price sheet | none |
| Module 2 | Energy rate of the grid fee falls to 40% | separate meter for the wallbox |
| Module 3 | Time-variable grid fee in three price levels, since April 2025 | intelligent metering system (smart meter), only together with Module 1 |
The grid operator grants the reduction to your electricity supplier. According to the Bundesnetzagentur, the supplier is not obliged to pass it on to you. Whether your tariff does so is stated in the supplier's terms and conditions.
What does a wallbox need in the building?
A wallbox needs its own circuit, its own residual current protection and space in the meter cabinet. The requirements for electric vehicle charging points are set out in DIN VDE 0100-722. Whether the existing service connection is sufficient depends on the charging power and on the rest of the building's consumption.
- Dedicated circuit: under DIN VDE 0100-722, every charging point gets its own circuit with a miniature circuit breaker.
- Residual current protection: every charging point has its own residual current device (RCD). If the wallbox detects DC residual currents itself, Type A or F is sufficient; otherwise Type B is required.
- Meter cabinet: it needs space for the additional protective devices and for the control equipment under § 14a EnWG. If there is not enough space, the meter cabinet must be adapted or replaced.
- Service connection: its capacity must cover the wallbox and all other consumption, especially at 22 kW or with several charging points.
For larger charging stations the grid operator may require a separate meter for the wallbox. You then need an additional meter position and a separate electricity contract. Module 2 under § 14a EnWG also requires a separate meter.
Can tenants insist on a wallbox?
Yes. Under § 554 BGB (German Civil Code), tenants can require the landlord to permit structural alterations for a wallbox. The landlord may refuse only if the alteration cannot reasonably be expected of them, even after weighing the tenant's interests. The costs are usually borne by the tenant.
Under § 20(2) WEG (Wohnungseigentumsgesetz, the German Condominium Act), apartment owners are entitled to reasonable structural alterations that serve the charging of electric vehicles. The owners' association decides by resolution how the work is carried out.
In underground car parks it pays to plan for several parking spaces with load management from the start. Otherwise the service connection reaches its limit as soon as several vehicles charge at the same time, and every additional wallbox counts towards the total under § 19 NAV.
Is there funding for private wallboxes?
In the Munich area, private wallboxes are currently supported only by individual municipalities. The City of Munich's “Förderprogramm Klimaneutrale Antriebe”, which also subsidised private charging stations, ended on 2 July 2025. The Bavarian State Government's “Förderprogramm Ladeinfrastruktur für Elektrofahrzeuge in Bayern 2026-2029” funds publicly accessible charging points, not wallboxes at private homes.
The Munich district has no programme of its own for wallboxes. According to the district office (Landratsamt), individual municipalities subsidise private charging stations, for example Grünwald, Pullach, Unterhaching and Unterföhring. Your municipality can tell you the amount and conditions.
Note: Funding information as of 31 October 2026. Programmes often change at short notice. Many programmes require you to place your order only after approval.
What the contractor checks on site
For a wallbox, the electrical contractor first checks the service connection, the meter cabinet and the cable route to the parking space on site. This shows which charging power is possible without reinforcement, whether the 12 kVA limit is reached and whether the meter cabinet has space for protective devices and control equipment under § 14a EnWG.
The following information helps at the first appointment:
- your latest electricity bill, which shows the grid operator and the meter
- model or data sheet of the wallbox you want
- your vehicle's maximum AC charging power
- photos of the meter cabinet and the parking space
- for rented property or an owners' association: the landlord's permission or the association's resolution
For registration, the contractor compiles the wallbox's technical data and submits them to the grid operator. Before commissioning, the installation is tested and the result is recorded in a test report. Reinlicht Elektrotechnik is an electrical contractor based in Taufkirchen and is listed in the registers of approved installers of the grid operators in our service area.